What causes a chainsaw to bind?
Either way, it is the compression that pinches your saw. If you start cutting from the top on a log supported at both ends, at some point the cut will close up and pinch your saw. Everything goes fine until the end of the log drops down and binds against the bar due to compression.
How do I stop my chainsaw from binding?
To stop your chainsaw from getting stuck, make a cut on top of the log or tree that’s preferably one-third of the log’s diameter. Use your chainsaw to cut from the underside until you meet the initial top cut. Always stand on the side when cross-cutting to prevent injury.
Why is my Husqvarna chainsaw blade not spinning?
If your chainsaw blade will not rotate, the chain may be tensioned too tight. If the chain is too tight, the blade may not spin when the throttle is engaged, which can cause damage to the clutch or other associated parts.
Why does my chainsaw keep jamming?
Indeed, whether it is a chainsaw electric ou thermal, it is the teeth of its links that come into direct contact with the wood and the materials to be cut. As a result, dirt, wear on the guide or links and even the motor can be the cause of jamming.
Can you straighten a bent chainsaw bar?
More often than not, chainsaw bars can indeed be straightened. But don’t take my word for it – do it only if the manufacturer states that this can actually be done. Trying to work on a bent saw’s bar which is not made for this sort of thing literally puts your life at risk. Be careful.
How do you cut a log without pinching it?
Placing small pieces of firewood under the tree or using wedges are two easy ways to prevent your chainsaw from pinching when you’re cutting up a tree for firewood that’s already on the ground.
How do I stop my chainsaw from leaking oil?
To avoid your chainsaw from leaking oil whist in storage, the best solution is to drain the chainsaw of its bar oil and fuel mix and store the chainsaw empty.
How do you cut down a tree without a pinching chainsaw?
The best way to free a trapped chainsaw is to use a felling wedge or a crowbar to gently lift the pressure and tension of the tree off of your chain and bar. Before attempting to do this the engine should be turned off to prevent the chain from accidentally moving and causing damage or injury.
Can a seized chainsaw be fixed?
If the saw has seized, it’s probably not worth fixing. One thing to look out for is damage to the main crank bearing. If it’s compromised, then the engine on an HD saw is basically toast.
How do you fix a chainsaw that won’t spin?
Easy fix, just loosen the bar-retaining nuts and rotate the tensioning screw counterclockwise to the correct tension. Then tighten the nuts back up.
What causes a chainsaw to not cut straight?
Uneven cutting teeth is often the cause. If the chain is cutting to the left that means the right teeth on the chain are longer, and vise versa. To correct, sharpen only the side with the longer teeth. If the bar has worn unevenly it will also cause the chain to not cut straight.
Why does my chainsaw bar keep bending?
A bent bar might cut crooked or straight, but, it will get hung up in the kerf. Unless you are using your bar as a pry bar or unless a log pinched it and a heavy weight bent it, then my bet is that the bar is straight. Bending a bar can happen but it happens to those who are not being careful.
Where can I find Husqvarna chain saw parts?
Browse through our complete listing of Husqvarna Chainsaw parts diagrams for every model of Husqvarna chainsaw ever made. We carry only original equipment Husqvarna Chain Saw Parts. Choose your Husqvarna model number and load the interactive diagrams to find Husqvarna chainsaw parts fast.
How to rewind a pull cord on a Husqvarna chainsaw?
Turn the starter pulley clockwise about two and one-half revolutions with your left hand, then counterclockwise one-half revolution. Hold the starter pulley in this position with your right thumb. Grasp the pull cord handle with your left hand and stretch the cord to remove slack.
What is the L screw on a Husqvarna chainsaw?
The T screw regulates how much fuel is sent to the carburettor while idling until the throttle is pressed. L Screw – With the chainsaw still running, take a screwdriver and turn the L screw clockwise.
What to do if your Husqvarna chainsaw starter is broken?
Put on safety glasses and gloves for protection from the spring uncoiling and propelling out of the starter housing, and for protection of your hands from sharp edges on the starter pulley. Place a new recoil spring into the bottom, center of the starter housing if the old one is broken.