Are all sink basket strainers the same size?
Kitchen sink basket strainers are the same size. The basket assembly can fit the sink drain opening every time. You don’t have to measure it, you don’t have to measure the size of your sink drain hole, this is the standard in the industry.
Can you connect utility sink to washer drain?
You CAN connect the sink to the standpipe, but it would not pass an inspection. You CAN use the washer p trap connection, after you cut off the P trap, for the washer and then drain the washer into the sink. This is an approved method.
What size is a utility sink drain?
Most sinks in a house will only require a 1.5″ drain when installing new piping. However the drain size for a laundry sink needs to be 2″ in diameter. A laundry sink is sometimes referred to as a utility sink is often located in the same room as the washer and dryer. A laundry sink needs to be 2″ instead of 1.5″.
How do you fix a slow draining utility sink?
Pour one-half cup baking soda into the drain followed by one-half cup white vinegar; the fizzing and bubbling reaction helps to break up small clogs. Block the drain using a small rag so the chemical reaction doesn’t all bubble up out. Wait 15 minutes.
How do you know what size sink strainer you need?
Don’t worry whether the strainer can fit your sink drain or not. The standard drain opening size is 3-1/2”, and some are 4”. This deep cup strainer can cover from 3-1/2” to 4” drain openings. If you are still concerned about the size, measure the diameter of your sink drain opening like below.
Do all kitchen sinks have the same size drain hole?
Whether you have a single or double basin sink, the standard drain hole diameter is 3-½”. Sink drains are available in a variety of finishes, so they can be matched with other kitchen fixtures such as faucets or cabinet pulls.
Does a washer need a utility sink?
Washers require 2″. The sink acts as a buffer to take the 30 gallons of water to drain at its own pace. Tieing in a 2″ line for the washer requires venting of the new line and often more difficult then simply draining into the laundry sink..
Can you drain a sink into a floor drain?
A sink needs to be connected to your sanitary sewer. The floor drain will be connected to your storm sewer. If you are in an older home, where they are shared, you could do it, but you will have to excavate the floor and make the connection sub-slab with rigid connections and not flexible hose or pipe.
How do you measure a utility sink?
Measure the sink width by placing your tape measure at the back edge of the sink (closest to the kitchen faucet) and stretching it across the sink basin to the front edge. Write down the width. Lastly, measure the basin depth. Place your straightedge ruler or your level across the top of your sink.
Can you use Drano in a utility sink?
You can use Drano® Clog Removers to unclog a kitchen sink, bathroom sink, shower or clogged bathtub, but DO NOT use them in toilets. For preventive drain cleaning, you can use Drano® Max Build-Up Remover in drains, toilets and even septic systems.
What is the standard size of a sink strainer?
Bar Sink Drain Openings A 2-inch sink strainer fits the standard bar sink drain. Drains connect to either a 1 1/4-inch or 1-1/2 inch tail pipe. These drains, like bathroom and kitchen drains, use a P-trap, which is a J-shaped pipe that connects to the main drain line.
What is the use of a kitchen strainer?
A kitchen device that is most used to strain liquids away from other ingredients but also to ocassionally sift fine ingredients away from larger ingredients. The Strainer may be formed as a spoon-shaped utensil or a basket-shaped strainer from various materials such as metal, nylon or cloth.
How do you remove a sink basket?
Procedure: 1. Remove the nut securing the drain line. 2. Use the sink basket wrench to remove the ears just above the nut. In some cases the basket only spins and thats when we use the holding wrench. 3. Lift the old basket out and clean the opening.
How do you replace a kitchen sink gasket?
Pry out the gaskets from both the hot and cold water inlet ports with a flathead screwdriver if you have a cartridge or ball-valve faucet. Take out the springs behind them as well and replace both the spring and the gasket. Place the new spring into the inlet then fit in the gasket.
What is the standard size of a kitchen sink?
The average kitchen sink measures 22-by-30 inches. While the front-to-back dimensions of the sink remain standard due to the size of most countertops and cabinets, the width of different types of sinks can vary dramatically.