How do I find my Moen faucet model number?

How do I find my Moen faucet model number?

Exact model numbers can be found on your box or on your instruction sheet. If unavailable, you may find the general family series number on the back of the spout (non pullout).

How do you replace the O ring on a Moen bathroom faucet?

How to Replace an O-Ring in a Moen Faucet

1. Shut off the water to the faucet beneath the sink.
2. Examine the handle of the faucet where the O-ring is located.
3. Use the appropriately-sized hex wrench to remove the hex screw holding the faucet handle in place.
4. Pull the old O-ring off of the valve body, and discard it.

Where do I find my faucet model number?

The model number is printed on a tag that is attached to the cold water supply line of the faucet. The supply line is located below the sink, countertop, bath rim, or behind the bowl of a bidet. The model number, or part number, is typically preceded by “P/N.”

How do I contact Moen free replacement parts?

Replacement parts may be obtained by calling 1-800-289-6636 (Canada 1-800-465-6130), or by writing to Moen Incorporated, 25300 Al Moen Drive, North OImsted, OH 44070-8022.

How do you take apart a Moen faucet?

Steps to follow to remove a Moen kitchen faucet

1. Step 1: Turn off water.
2. Step 2: Drain the pipes.
3. Step 3: Remove the handle.
4. Step 4: Remove the dome and plastic sleeve.
5. Step 5: Removing the handle mechanism.
6. Step 6: Remove the ring and washer.
7. Step 7: Remove the spout.
8. Step 8: Pull out the cartridge.

Why does my new Moen faucet drip?

There are generally two causes of water leaking from your Moen faucet. Because pull-out spray faucets have a single handle, the most common cause of the water leaking is the O-ring. Remove the handle by pulling straight up and exposing the cartridge body and O-ring. Remove the O-ring and replace it with a new one.

Why is my Moen faucet leaking?

How do I know what cartridge my faucet is?

Easiest of all is when it says the brand name right on the faucet face. But you should also look at the bottom of the faucet, on the handles or on the round plate behind the handles. If you find a brand name, go to the manufacturer’s website and call the contact number for assistance.

How do I find my bathroom faucet manufacturer?

The most obvious and quickest solution is to look for a logo — the manufacturer’s symbol — that identifies its faucets. Each manufacturer has a distinctive logo that sometimes appears on the escutcheon — the plate beneath the faucet — the body of the faucet, the spout itself or somewhere on the handle.

Are Moen kitchen faucets guaranteed for life?

From finishes that are guaranteed to last a lifetime, to faucets that perfectly balance your water pressure, Moen sets the standard for exceptional beauty and reliable, innovative design. All Moen products come with a Limited Lifetime Warranty against leaks, drips and finish defects.

What is Moen faucet warranty?

Moen warrants to the original consumer purchaser for as long as the original consumer purchaser owns their home (the “Warranty Period” for homeowners), that this faucet will be leak- and drip-free during normal use and all parts and finishes of this faucet will be free from defects in material and manufacturing workmanship.

Do Moen faucets have washers in them?

However, Moen faucets are designed with cartridges, and it is these you replace and not washers per se. Whichever Moen faucet model you have, you need only a few tools, a few minutes and a little patience to replace Moen faucet cartridges.

How do I replace bathroom sink faucet handles?

Replace Bathroom Faucet Handles In Six Steps Step 1 — Remove Cap Cover Step 2 — Remove Retaining Screw Step 3 — Remove Old Handle Step 4 — Insert New Handle Step 5 — Secure with Screw Step 6 — Add Cap